港口大直径筒仓锥壳受力分析及施工支撑体系优化研究
DOI:
CSTR:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Mechanical analysis of conical shells and optimization of construction support systems for large-diameter port silos
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对大直径筒仓锥壳倾角参数对结构受力影响规律不明确,以及施工支撑体系传力复杂等问题,以40 m大直径混凝土筒仓为工程背景,开展锥壳受力与施工支撑体系的优化研究。采用有限元方法建立不同锥面倾角模型,分析倾角变化对锥壳内力分布和变形响应的影响;在此基础上,提出“贝雷桁架+中心立柱”施工支撑体系,并对不同布置方案的受力性能和经济指标进行对比。结果表明:随着锥面倾角增大,锥壳拱压效应增强,底部环向拉力及竖向变形逐渐降低,但刚度提升幅度呈递减趋势;在所分析参数范围内,45°倾角具有较合理的综合受力特征,相较30°倾角,底部环向拉力降低37.2%,顶部竖向变形降低34.5%。分级变间距布置方案较等间距方案最大挠度降低27%,钢材用量减少5.2%,措施费用降低约12%,搭设周期缩短约15%。研究结果可为类似大直径筒仓锥壳设计及施工支撑体系选型提供参考。

    Abstract:

    To address the unclear influence law of cone angle parameters on the mechanical behavior of large-diameter silo shells and the complex load transfer characteristics of construction support systems,a 40 m diameter reinforced concrete silo is selected as the engineering background to investigate the mechanical behavior of conical shells and the optimization of construction support systems.Finite element models with different cone angles are established to analyze the effects of cone angle variation on internal force distribution and deformation response.Based on the analysis results,a “Bailey truss + central column” support system is proposed,and different layout schemes are compared in terms of mechanical performance and economic indicators.The results show that increasing the cone angle enhances the arching effect of the conical shell,reducing the circumferential tensile force at the bottom and vertical deformation,while the improvement in stiffness gradually decreases.Within the investigated range,the 45° cone angle exhibits a relatively reasonable overall mechanical response.Compared with the 30° case,the bottom circumferential tensile force and the top vertical deformation are reduced by 37.2% and 34.5%,respectively.Compared with the uniform-spacing layout,the graded variable-spacing layout reduces the maximum deflection by 27%,steel consumption by 5.2%,construction measure cost by approximately 12%,and construction period by approximately 15%.The results can provide a reference for the design of conical shells and the selection of construction support systems for similar large-diameter silos.

    参考文献
    相似文献
    引证文献
引用本文

庞 辉.港口大直径筒仓锥壳受力分析及施工支撑体系优化研究[J].水运工程,2026(10):142-150.

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-10-16
  • 出版日期:
文章二维码